Hitachi Seiki Ht20sii Manual
I have a Hitachi Turn 20S II It has a Seicos Mark II controller. I have never seen this problem before. Do you have an error number?
Hitachi Seiki Manuals Instruction Manual and User Guide for Hitachi Seiki. We have 30 Hitachi Seiki manuals for free PDF download. Hitachi Seiki HT25SHT40S Lathe Wiring Manual. Seiki Seicos 10M 16M 18M Programming Instruction Manual. Hitachi Seiki VM VK VS HG HS Programming Manual.
Or alarm number? I can look it up in the manuals if you dont have them. Also i am in So-Cal area, and we have a GREAT Hitachi repair man that i could refer you too if need be. PS: just incase, When you see the PC not ready alarm, are you sure its not 'Machine not ready'?
Because there is a 'STANDBY' button on the controller. Once the 'Machine not ready' signal comes up, you are supposed to push the 'STANDBY' button and hold it down for about 1 second. Do this, and if you still have the problem, let us know an Alarm / Error number if you can. Good luck Hi Gary E.
I dont know if this will work for that alarm but give this a shot. Turn the power off to the machine.Get 2 other people to help you or really stretch out your fingers.Press the cycle stop,reset, and the spindle stop buttons all at the same time and while holding them down have someone power the machine back up then have the other person press the standby button all the while keep holding the 3 buttons down.
Hitachi Seiki Technical Support
After the standy button is pressed release the buttons and hit reset and see if the alarm dissappears. This works when he turret over ndexes past a tool station and it works to clear a few other alarms also. If that dosent work I dont know what is wrong with it. I dont know if this will work for that alarm but give this a shot. Turn the power off to the machine.Get 2 other people to help you or really stretch out your fingers.Press the cycle stop,reset, and the spindle stop buttons all at the same time and while holding them down have someone power the machine back up then have the other person press the standby button all the while keep holding the 3 buttons down. After the standy button is pressed release the buttons and hit reset and see if the alarm dissappears.
This works when he turret over ndexes past a tool station and it works to clear a few other alarms also. If that dosent work I dont know what is wrong with it. Good luck!!Just out of curiosity.my machine (Seicos III control) has no button labeled 'cycle stop'.by that do you really mean 'feed hold' or?? Also, by 'turn the power off' do you mean the 'off' button at the control or the main breaker in the back??
Makes a huge difference, since if control power only. It would be possible to do this with one person, but if main power breaker in back two people would be absolutely essential.
Hello all out there lost in the confusion of trying to find support for your Hitachi Seiki machines. I own a CNC Service Company in Wichita Kansas working on all brands of machines, but specializing in Hitachi Seiki. I currently have over 10 gig of info on Hitachi Seiki machines in my database from machine software to procedures and ELECTRICAL MANUALS!!!!! I have years of experience working with these machines, and until June of 04 I worked for Mori Seiki in LA as the Hitachi Seiki specialist. We DO travel, and my hourly rate for shop labor is only $75.00 per hour no matter what state your in. I also do phone support and provide procedures at $45.00 per hour 1 hour min.If you have a Hitachi Seiki machine, other machine models welcome also, call us and we will be happy to help!!! (cureing your headaches is free!!) You can contact us at 316-744-0549 just ask for Josh, aka Hitachiman well be looking forward to hearing from you!!!
Hello, Here a question from Stefan Beerens of the netherlands. I have a hitachi seiki turning machine st200 who needs new bearrings in the main spindel.
It's not built in spindel but with belts. Can anyone give me an adres for new bearrings for this machine. Is my mail adres. Thanks a lot. Best regards Stefan Beerens Hello all out there lost in the confusion of trying to find support for your Hitachi Seiki machines. I own a CNC Service Company in Wichita Kansas working on all brands of machines, but specializing in Hitachi Seiki. I currently have over 10 gig of info on Hitachi Seiki machines in my database from machine software to procedures and ELECTRICAL MANUALS!!!!!
I have years of experience working with these machines, and until June of 04 I worked for Mori Seiki in LA as the Hitachi Seiki specialist. We DO travel, and my hourly rate for shop labor is only $75.00 per hour no matter what state your in. I also do phone support and provide procedures at $45.00 per hour 1 hour min.If you have a Hitachi Seiki machine, other machine models welcome also, call us and we will be happy to help!!! (cureing your headaches is free!!) You can contact us at 316-744-0549 just ask for Josh, aka Hitachiman well be looking forward to hearing from you!!! Hello, I have Hitachi Seiki VK55II machine with Seicos 10 control.
Battery alarm started to appear on screen of control. I can reset alarm but it appears again every 10-15 days. I don't have proper support of that machine and I'am lack of documentation.
Can you help me with procedure for battery changing? Also need help with data backup before battery changing. I will appreciate for any kind of help. In case of any controllers, we should keep ready with fresh and tested set of batteries and without switching of CNC, we should replace batteries, keeping in mind the polarity, with this backup will not get lost. Hope replacement of batteries will solve the issue. My name is Josh and I am the Hitachi Man. I have been hard to reach off and on for awhile now.
Due to a huge down turn in business I had to take the work I could get. I am starting to see the light at the end of the tunnel as things are starting to pick back up again though! I am going to post my email address on here for anyone and everyone that has or comes up with Hitachi Seiki problems. I may be in a position very soon that would allow me to travel again, in which case I could start scheduling service for those of you who need it. So lets see how this works!! I am firing my business back up. Feel free to contact me at: this is a sure fire way to make sure I get the message and I WILL get ahold of you, I get these emails on my phone too!!
Josh Hi Josh, I'm Tom from Phoenix. I am having a problem clearing the X and Z axis over travel alarm on a Hitachi-Seiki TS15 using a Sigma 21L control.
So far I moved the ball screws manually off of the hard stop/limit swithes, but I can't seem to clear alarm. I don't mean to brag, but I have over 20 years experience in causing alarms to happen, but even that hasn't helped. I haven't cracked the electric panel yet, only because my instincts tell me 'its Forbidden!' Any help would be appreciated. I am an ex-musician.
I'll give you free singing lessons via mindmeld Thanks. Hello all out there lost in the confusion of trying to find support for your Hitachi Seiki machines. I own a CNC Service Company in Wichita Kansas working on all brands of machines, but specializing in Hitachi Seiki.
I currently have over 10 gig of info on Hitachi Seiki machines in my database from machine software to procedures and ELECTRICAL MANUALS!!!!! I have years of experience working with these machines, and until June of 04 I worked for Mori Seiki in LA as the Hitachi Seiki specialist. We DO travel, and my hourly rate for shop labor is only $75.00 per hour no matter what state your in. I also do phone support and provide procedures at $45.00 per hour 1 hour min.If you have a Hitachi Seiki machine, other machine models welcome also, call us and we will be happy to help!!! (cureing your headaches is free!!) You can contact us at 316-744-0549 just ask for Josh, aka Hitachiman well be looking forward to hearing from you!!!
I bought cnc machine of spec:Hitachi Seiki HT25DM, Fanuc 11TT, Twin turret, C Axis, Top turret with live tools.(see attached pictures) I recently installed this machine by giveing properly connection to this machine. When i power on the machine then machine dnt give any alarm and machine is ready for operation except 'inter fence check inneffective led power on'i mentioned red line to led of control panel' see picture of control panal. I am not understanding this meaning may be it is safety but i dnt know how should i remove this. Firstly i wana to know this becuase machine's is ready for operation but there is no axis moves.
Please advise me to solve this matter. Best Regard, Muhammad Nadeem Ashraf Attached. Dear All I have a hitachi machine and facing following problem,can any one help me to get a soft copy of pc ladle. Following are the details. Problem - PLC DATA LOST ON HITACHI SEIKI HG500 Service Required - A Soft Copy of PC LADLE.( We have a communication software and cable for uploading Machine Details Model- HG500 CNC -FANUC 15 MA SR No -HG50229 PLC - Hitachi Seiki make MICON 16 II Specifications- Normal Ladle Program No-2741-A02T(Mentioned in the electrical diagram book) cncrepairs. I bought cnc machine of spec:Hitachi Seiki HT25DM, Fanuc 11TT, Twin turret, C Axis, Top turret with live tools.(see attached pictures) I recently installed this machine by giveing properly connection to this machine. When i power on the machine then machine dnt give any alarm and machine is ready for operation except 'inter fence check inneffective led power on'i mentioned red line to led of control panel' see picture of control panal.
I am not understanding this meaning may be it is safety but i dnt know how should i remove this. Firstly i wana to know this becuase machine's is ready for operation but there is no axis moves. Please advise me to solve this matter.
Best Regard, Muhammad Nadeem Ashraf I can solve your problem free of cost call me on 00981 my mail id is =. Dear All I have a hitachi machine and facing following problem,can any one help me to get a soft copy of pc ladle.
Following are the details. Problem - PLC DATA LOST ON HITACHI SEIKI HG500 Service Required - A Soft Copy of PC LADLE.( We have a communication software and cable for uploading Machine Details Model- HG500 CNC -FANUC 15 MA SR No -HG50229 PLC - Hitachi Seiki make MICON 16 II Specifications- Normal Ladle Program No-2741-A02T(Mentioned in the electrical diagram book) cncrepairs i can send give your contact details. Regards Prabhat Mishra +981. Hi, When starting spindle by MDI at speed 500 rpm for boring soft jaws. Alarm No 520 appears saying 'Spindle start impossible, Check door close, chuck close and center position'. Door close LED is ON, both the chuck proximity switch also ON (LED ON) i cannot find location of center position LED or proximity switch.
Hitachi Seiki Ht20sii Manual
How to confirm about center position. Machine is Hitachi Seiki HT20SII. I have its programming manuals but no operation manual. An help in this regard will be highly appreciated.